drill press DIY slow speed pulley - Custom Fighters - Custom Streetfighter Motorcycle Forum

Go Back   Custom Fighters - Custom Streetfighter Motorcycle Forum > Technical Section > Heavy Metal

Heavy Metal Anything to do with welding, bending and fabricating things from metal goes in here.

CustomFighters.com Streetfighter Motorcycle Forum > drill press DIY slow speed pulley

Reply
 
Thread Tools
Old Streetfighter Motorcycle Forum Post 04-28-2016, 03:29 PM   #1
fredycruger
fuck your face

CF Lover
fredycruger's Avatar on CustomFighters.com Streetfighter Motorcycle Forum
I support CustomFighters.com Streetfighter Motorcycle Forum
Local Time: 07:47 AM
Location: Massachusetts
Posts: 832
Flip Offs: 8
Flipped Off 10 Times in 6 Posts
fredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud of
Winter Buildoff Winner 
Default drill press DIY slow speed pulley

should work on any drill press that has adjustable Head


I cut 1.5" off from the tube that holds the head and table

welded 1/8"plate on top of the cut off ,drilled 1/2" hole
welded 3" x 1/2" bolt inside
bolted pulley
raised head up right up to edge of 'clamp' and just dropped the pulley in the hole
took me about 2 hrs to do it

pulley is 4 step 4L 3/4" bore ... ebay -17$
2 Bronze bushings ...Oilite Flange Bushing Bronze New 1/2 id x 3/4 ebay - 9$
3" bolt with nilock nut 3$
2 belts - 28" and 29"

the idea is to have bolt off center so you can use it to tension front belt
than tighten rear belt by moving motor to hold it in place
im not sure if I need any set screw on the middle pulley it fits nice and tight in the bore









pulley with brass bushings inserted












fredycruger is offline   Reply With Quote on our streetfighter motorcycle forum
These people High Fived fredycruger!

Advertisement
These advertisements only appear for guests, register now for free to remove these ads!
Sponsored Links
Advertisement
 
Old Streetfighter Motorcycle Forum Post 05-02-2016, 11:06 AM   #2
Fight Everything
Rollin hard in Wiscompton

CF Pimp
Fight Everything's Avatar on CustomFighters.com Streetfighter Motorcycle Forum
I support CustomFighters.com Streetfighter Motorcycle Forum
Local Time: 06:47 AM
Location: Dirty MKE, Wi
Posts: 3,687
Flip Offs: 55
Flipped Off 45 Times in 35 Posts
Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!Fight Everything is an amazingly helpful member with a good attitude!
Supporter of the Streetfighter Build for Charity 
Default Re: drill press DIY slow speed pulley

Well apparently my latest posts never actually posted. I think I just found a glitch in the updates. Anyway, maybe I'm missing something, but how do you rotate and lock down the tensioner?
Fight Everything is offline   Reply With Quote on our streetfighter motorcycle forum
Old Streetfighter Motorcycle Forum Post 05-02-2016, 01:28 PM   #3
fredycruger
fuck your face

CF Lover
fredycruger's Avatar on CustomFighters.com Streetfighter Motorcycle Forum
I support CustomFighters.com Streetfighter Motorcycle Forum
Local Time: 07:47 AM
Location: Massachusetts
Posts: 832
Flip Offs: 8
Flipped Off 10 Times in 6 Posts
fredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud offredycruger has much to be proud of
Winter Buildoff Winner 
Default Re: drill press DIY slow speed pulley

Quote:
Originally Posted by Fight Everything View Post
Well apparently my latest posts never actually posted. I think I just found a glitch in the updates. Anyway, maybe I'm missing something, but how do you rotate and lock down the tensioner?
I turned it with pliers and rear belt holding the front one tensioned

so there's no need for locking it down
it sits pretty tight in the bore

fredycruger is offline   Reply With Quote on our streetfighter motorcycle forum
Reply

  Custom Fighters - Custom Streetfighter Motorcycle Forum > Technical Section > Heavy Metal

Bookmarks

Thank you for viewing drill press DIY slow speed pulley in the Heavy Metal section of our streetfighter motorcycle forum. I hope you found it useful!


Thread Tools

Forum Jump

Heavy Metal - drill press DIY slow speed pulley on Custom Fighters Streetfighter Motorcycle Forum

All times are GMT -4. The time now is 07:47 AM.



Powered by vBulletin Version 4.20
Copyright ©2000 - 2020, Jelsoft Enterprises Ltd.
User Alert System provided by Advanced User Tagging (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.
vBulletin Security provided by vBSecurity v2.2.2 (Pro) - vBulletin Mods & Addons Copyright © 2020 DragonByte Technologies Ltd.