Here is a pic of it in action.....just to prove that it does work. :shocker:

 

How can I get plans for this?

 

Man I wish I knew how to weld...very well done!!!

 

MIG welding is pretty easy. In fact, welding is the easiest part of any project - it's the metal fabbing, forming, cutting and prep that's the tough part <-- IMO.

 

That is a very cool set up.
I've been playing with the idea of a similar set up in my head for a while now.

I would be interested in how your pivot points hold up and it there will be any issues with bolt holes going oval.

What lifting capacity does that ram have?

 

I doubt there will be any oval hole issues. I sleeved all 16 of the pivot points with 1" schedule 80 pipe (5/8 I.D. to match the bolt size) to help disperse the weight load.

The ram has an 8 ton lifting capacity. I don't really need that much (obviously), but it was the most cost effective ram that was air over hydraulic. I think it was around $100.

I looked all over the internet for home built lift ideas, and found a bunch of junk that I wouldn't put a clapped out 10-speed on.

 

I think that I didnt see all the pics the first time I looked at it sorry.

I didn't see that you sleeved the main frame too, thought it was only your lift arms.

How big is the main platform? How do you find the 3' working height?

You're right about the lack of decent builds on the net. They are normally those wooden fixed ones aren't they.
I originally planned to make a scissor like layout but there will be a lot of extra work with that I think. This looks much simpler and effective.

Have you considered adding a ramp or triangle on the safety stops? so that when you raise the lift the safety arm just slides on over?

So like a triangle to the right side of the stops in this pic.

 

I think that I didnt see all the pics the first time I looked at it sorry.

I didn't see that you sleeved the main frame too, thought it was only your lift arms.

How big is the main platform? How do you find the 3' working height?

You're right about the lack of decent builds on the net. They are normally those wooden fixed ones aren't they.
I originally planned to make a scissor like layout but there will be a lot of extra work with that I think. This looks much simpler and effective.

Have you considered adding a ramp or triangle on the safety stops? so that when you raise the lift the safety arm just slides on over?

So like a triangle to the right side of the stops in this pic.

The main platform is 2'x8'. The two safety stops are set at 2.5' & 3.0'. I actually had to do a little geometery to figure out the length of the lift arms, stop positions and safety catch length. Not to mention that you have to factor in the height of the lift off the ground in the calcs to get the overall height. I really probably over analyzed it - but I am pretty anal that way. Let's just say I measured 40 times and cut once.

I thought about doing a scissor lift as well, but decided there were too many moving parts.

No need for a ramp on the safety stops. The saftey bar glides right over them during lift. There is only resistance and the safety bar when it is under load. To lower the lift, I simply raise it up, lift the safety bar up to clear the safety stops, then release the air pressure and down she goes.

I have considered adding an attached loading ramp for the bikes. Right now I just use the same one I do when loading them into my truck. It works ok.

 

How much $$$ did you spend on materials?

 

All in all, around $500. I know you can totally buy one for that - but that's not as much fun as building your own - IMO. Besides, this one is made in the USA! :rock:

 

Cool man!

I thought about building one, but I guess I don't like having the bike up that high - I mean I never have so I guess I don't really know if I would like working on it at chest/waist level. I've always used axle/swinger lifts for as high as I needed. Very nice work though man!

Nate

 

Thanks man. Working on a bike, without having to bend over or get on your knees is the only way to go. Bending over, and getting on your knees is women's work!

 

very nice job!!! arty-smiley:

 

Thanks!

 

So damn cool looking.

 

Thanks! I think is pretty cool lookin' too.

 

Would you by any chance share your plans? Looks like you already did the brain work very well.

 

Don't really have any plans I can just post up. Just a lot of graph paper with chicken scratch calculations. If there are specific measurements or info you want - let me know.

 

This looks eerily familiar.

http://www.customfighters.com/forums/showthread.php?t=50157&highlight=motorcycle+lift

 

This looks eerily familiar.

I saw a version of that one online when I was building mine. I didn't like the angle iron construction, safety mechanism, or use of an automobile floor jack of the one I saw. I also saw a video of it in action and you could see the angle iron flexing under load. Not for me. I wanted one that was stout, and I could roll around the shop.

It's not like anyone is really going to reinvent the wheel here. There are only so many ways to build a motorcycle lift. More than likely you're going to build this style or the scissor lift style. In my opinion, this design is easier to build, and is very functional. Of course, my opinion is biased

 

I totally understand. I just found it funny that it was a couple weeks after I started the thread I linked to that you posted this. The steel I used in my testing wasn't as thick as what you've used but it's still good to see my setup isn't a total failure.



Any idea how much yours weighs? I used angle in my setup to try and save weight. I think I mentioned somewhere in the other thread that what I did will only weigh ~150# max when it's all done. One thing I would look into is a way to keep the lift from rolling. Maybe make some feet that lower to get it off the wheels once it's positioned? I planned on using a large bolt in each corner with a rubber/plastic pad on the end. The large bolt would also allow you to level the surface if you wanted to put something like a frame jig on it.

 

I have had a couple of PM's for some measurements. So here they are:

 

this is going on my list of things to do. thank you very much. you saved me a lot of hassle.

 

Dig the design, kinda reminds me of mine. I also added pads along the side to bolt the chassis jig on to, and a drop out door for doing oil changes.

 

Hi buddy,

Could you send me the plans of your table? This is amazing!!!

Regards,

Pedro

Couple of shots of the initial mock up:

The Torin Air Over Hydraulic 8 Ton Ram. This is what gets the bike from the ground to the working height in 10-15 secongs:

This is the lockout mechanism that holds the lift up at 2.5' & 3.0'. It works really well too. No danger of this thing coming down and someone losing a limb. The beauty of it is that it collapses out of the way when the lift is at rest height:

Air Release Handle:

Rolling Framework. Front tie down hooks added:

3/16" Plate steel top welded in place:

Painted Up and Ready for Work:

[/QUOTE]

 

i almost copied this table and it is a great tool! i did minor changes to locking mechanism, cylinder mount, mounted the lift arms on top of the bottom frame instead of inside for added strength. and axles through the whole table on upper lift points. i used bushings in all the lifting points. posting some pictures to share my changes.

 

i almost copied this table and it is a great tool! i did minor changes to locking mechanism, cylinder mount, mounted the lift arms on top of the bottom frame instead of inside for added strength. and axles through the whole table on upper lift points. i used bushings in all the lifting points. posting some pictures to share my changes.

Nice work. Always nice to see other fab work. What was your train of thought behind the cylinder mount? Seems like the ram needs to go a long way out for the table to reach working height. How long does it take for the ram to take the table from floor to operating height? Nice Job!

 

What was cost of materials

I figure it would cost around alot I've been trying to look around on job sites for scrap with no luck

 

how much is 50 feet of sprinkler pipe and some sheet metal?

 

With the materials he used, here in the states, 60' of 3/16 2x2 will run you close to $200. A 4x8 sheet of 3/16 (even though you only need half, maybe you could split it with someone) is about $250. The ram I believe is about $60 and then various nuts and bolts, welding wire etc etc id say your looking at close to $600 in materials alone.
And before anyone says it, sure the harbor freight one is cheaper but it is no where near the quality as the table he built here with the heavy duty materials.

 

Something for me to do in the future

Sent from Motorcycle.com App

 

old thread bud, doubt youlll get a reply. BUT, theres a pic with measurements in the thread and you can probably reverse engineer it from there.

 

Hi Guys,

This thread inspired my bike lift table and I thought I would post some pictures to help others. I made mine out of 75x50x3 RHS for the main frame and 50x50x4 SHS for the ram mount and sheet supports. I used a 8 ton ram I brought on ebay that has hydraulic or air to move the ram. I used 3mm Gal sheet for the top. I dont have a picture yet but I brought a bolt on wheel clamp from ebay.

 

nice job

 

Consider this design well and truly stolen!! looks great I have an old 12 foot car transporter trailer chassis made from 2" box to cut up for it and me sheds nearly built and ready too yay!!